ANCEL S3000 New Model DC12V Automotive Smoke Machine Leak Detector for Cars/Motorcycles/Trucks/Boats/ATVs
ANCEL S3000 Main Selling Points:
✔️ Built-in Air Pump Saves Time and Money: You’ll have to buy an air compressor in addition to the detector in most cases to be able to test your vehicles for leakages, ANCEL S3000 car fuel leak detector already has that feature built-in. So you’re saving some extra money!
✔️ Dual Testing Model: ANCEL S3000 EVAP Leak Testers come with a dual testing model including air mode and the smoke mode. Air Mode:Independent controlled built-air pump. Smoke Mode: Independent controlled smoke generator. These enable you detect the leaks precisely.
✔️Instant Smoke Generation: Press Smoke Control switch, the LED Indication would turn GREEN, and the car smoke tester start to generate smoke within seconds. One of the biggest hassles with the automotive smoke machines is the time of heating of the device. You won’t have to wait for the tester to warm up with ANCEL S3000 fuel leak detector.
✔️ Overload Protection: ANCEL S3000 automotive fuel leak detector has built in self-protective system:Overheat and Anti-frost Protection. When the temperature of the device exceeds 120℃, power protection will be intelligently activated to turn it off. The device can also work normally at -20℃. You don’t have to worry about switching on and off the machine constantly during diagnosis. The system takes care of the load for you.
✔️Wide Compatibility:ANCEL S3000 car smoke detector used to detect leakage of pipe systems on automobiles, motorcycles, snowmobiles, ATVs, light trucks, and speedboats. The smoke machine automotive is suitable for all makes and models of cars.
✔️Various System Test:Crankcase System Test; Intake System Test; Car Sealing Test; Fuel Tank System Test; Turbo System Test; EVAP System Test; Exhaust System Test; Various Pipe Fittings Test. (Note: Not applicable to air conditioning system piping, Lamp housing) It can quick to find evap leaks.
✔️ Save Money by Using Baby Oil or Mineral Oil: You don't need to buy expensive smoke oil. Use baby oil, Pure #5 white oil is the best choice if available. This makes ANCEL S3000 smoke machine automotive practically free to use forever!
✔️Easy To Use: The Smoke Machine Automotive with easy-use function and portable design, can help mechanic produce lots of smoke within 30s to detect the leaks in pipe system, dramatically reducing diagnostic time.
ANCEL S3000 ADVANCED TECHNOLOGY:
Oil Refifill Port: For oil refifill while its needed. The funnel is a nice helper to prevent oil from poured to the surface of the unit Velcro Strap For collection of the smoke delivery hose, and power cord before storage.
Smoke Outlet Port :While set up the unit, the Smoke Delivery Hose need to be mounted onto the Smoke Outlet .
Power Socket: While set up the unit, the power cords need to plug into the power socket.
State Indication and Air Control:The LED Indication has two states. RED: Power ON. GREEN: Pressurized air production. While power up the unit, the LED would turn RED. Press Air Control switch, the LED Indication would turn GREEN, and the unit start to generate pressurized air. Press Air Control switch again anytime, the LED Indication would turn RED, and the unit stops generating pressurized air.
State Indication and Smoke Control:The LED Indication has three states. OFF: Smoke generation not started. GREEN: Smoke generation. RED: Overheat. While not smoke the unit, the LED would be OFF. Press Smoke Control switch, the LED Indication would turn GREEN, and the unit start to generate smoke. Press Smoke Control switch again anyitme, the above LED Indication would turn OFF,and the unit stops generating smoke. While the smoke generating chamber is overheat, for protection, the smoke generation would be halted and the LED Indication would turn RED and restart generating smoke while the smoke generating chamber cooled down, or you can switch it OFF by pressing Smoke Control switch.
System Pressure Gauge: The Pressure Gauge displays the output pressure of the machine if block the smoke outlet port, otherwise it shows the real time pressure of the system been testing.
Flow Meter: The purpose of the flow meter is to provide a quick visual indication of the amount of air/smoke passing through the system being tested. If the smoke nozzle is in a closed system, and there are no leaks in that system, the flow meter will read zero (ball at bottom of scale). As the system is filled with air or smoke, the ball in the flow meter will slowly fall to the bottom of the scale as the pressure in the system equalizes to the output pressure of the unit. As the flow decreases, the output pressure will increase. If the flow meter ball never falls to the bottom of the scale, there is leakage or air passing through the system. It is not necessary to use smoke when using the flow meter to determine if a leak exists.
Flow Dial: In many cases excessive smoke existing a leak may make it difficult to determine the exact location of the leak. The purpose of the Flow Control Valve is to decrease the amount of smoke existing a leak so that its position may be pinpointed without the masking effect of excessive smoke. Turn clockwise to decrease flow, counterclockwise to increase flow. This valve is also used to lock out the system under test and observe any pressure decay on the pressure gauge.
Oil Level Gauge: While set up the unit, smoke oil need to be filled into the unit, do not exceed the MAX line. Check and confirm proper oil level periodically. If the oil level is lower than the MIN line,the unit would need a refill.
How to do leakage test？
1. Turn OFF the ignition of the vehicle.
LEAK TEST OF VEHICLE SYSTEMS REQUIRES THE ENGINE TO BE OFF
2.Dismantle the air filter and the throttle connections.
3.Clean the inner wall of the intake opening to avoid sharp objects and put the Universal Intake
Adapter into the opening
4.Connect the Power Cord to 12V vehicle battery.
5.Now the Power LED would be ON, if else check the power supply.
6.Introduce the smoke nozzle into the system via the Adapter Cone
7.Press Air Control Switch, wait for 30 seconds until the system is pressurized, and check the Pressure Gauge & Flow Meter reading for leak status, if the unit is equipped with Pressure Gauge & Flow Meter
8.Press Smoke Control Switch, .unplug and Plug back the smoke nozzle back into the Cone Adapter when there’s obvious smoke coming out of the smoke nozzle
9.The system will be ready for leak check in 2 minutes. Use a bright light torch or working lamp to assist
10.After test, press Smoke Control Switch again to stop the unit from generating smoke and
press Air Control Switch to stop generating pressurized air
11.Collect the Smoke Hose and the Power Cord with the Velcro Straps for storage. Hang the unit or make it stand in UPRIGHT position only. Do NOT lay it down.
Note:
1.When you use this ANCEL S3000 Car Smoke Leak Detector for the first time, fill with 20ml oil . Please be careful NOT to beyond this range.
2.The testing liquid : both liquid paraffin and baby oil are OK.
3.Fresh oil can be filled with only when the smoke gets thin, and it can’t be filled over 20ml each time.
4.Before filling fresh oil, please pour out the left oil in the detector & replace the detector oil regularly.
5.During the process of leak detection, please keep away from smoke-sensitive parts.
6.Do NOT run the detector over 8 minutes continuously. It needs interval rest.
7.The detector has an intelligent protector, if it exceeds the working limit, such as over 75 ℃, it will automatically turn off the power. In this case, please operate it later.
8.The round part of this detector has temperature, please be careful to avoid burns.
9.If the test pipe needs to be disconnected in the middle, please secure the other side with a rubber stopple.
Independent switch control design
🔥Air Mode: Independent controlled built-air pump.
🔥Smoke Mode: Independent controlled smoke generator.
Wide Range of Applications
For detecting the leakage of pipe systems on cars, motorcycles, snowmobiles, SUV, ATVS, Light Turks, Speed Boats.
Overheat & Anti-frost Protection
This smoke detector is equipped with the latest intelligent protection device. When the temperature of the device exceeds 75 degrees Celsius, the power protection device will be intelligently activated to turn it off, to ensure the safety of the operator and the device. The device is also suitable for low temperature operation.
Leak Status Indication
By observing the pressure gauge, allowing you to clearly understand the leakage state of the vehicle.
No Leak, Small, Leak or Massive Leak.
Product Parameter：
Power Supply: DC12V
Output pressure: 0.5~0.8 bar
Air pressure output: built-in air pump
Main unit dimensions:85×130×185mm
Length of Power Cord: 2.5 Meters
Length of Smoke Hose: 2.5 Meters
Comparison of S3000 with S1000 and S2000
ANCEL S3000 Packing List
1*Power Cord: To offffer connection from the unit to the automobile battery, in order to drive the unit.
1*Funnel:Assistance method for smoke oil refifill, to prevent pour oil to the unit surface.
1*Hook up: To hang the somke machine in the car
1*User Manual: Detailed descriptions about how to use the smoke machine automotive.
1*Intake Bladder:To fifit the intake and exhaust, seal the system and introduce smoke into the system. Especially while the inlet position is not rounded-shape.
1*Adapter Cone: To fifit the intake and exhaust, seal the system and introduce smoke into the system. It may fall out at high pressure and need a second hand to push and hold at operation.
1*Replacement Rubber: The rubber on the Intake Bladder may be easily broken, if not operate it properly with caution.The rubber could be replaced with new one without replace the whole Intake Bladder.
1*Smoke Delivery Hose: For introduction of smoke from the unit to Adapter Cone / Universal Intake Bladder or to the vacuum pipe directly.
