F4 F405 Flight Controller:
Product Parameters:
MCU: STM32F405RGT6 168MHz
Gyroscope: Mpu6500
Baro:Bmp280
OSD: Betaflight SPI OSD DJI HD OSD(UART5)
Black box: 16MB
6x Uarts: UART 1/2/3/4/5/6
4x PWM outputs
1x I2C
2x LEDs for FC STATUS (Blue) and 3.3V indicator(Red) and 5V indicator(Red) and 9V indicator(Red)
USB Type-C(USB2.0)
1x JST-SH1.0_8pin connector (Gnd/Vbat/S1/S2/S3/S4/Curr/Rx3)
1x JST-SH1.0_6pin connector (9V/GND/T5/R5/GND/R2)
VTX 9V filtered power
DJI FPV OSD is supported by any spare UART
LED: 4 LED independent pads, support WS2812 programming lamp output.
Receiver: Support Sbus, crsf, ibus, SBUS, XBUS receiver,
The default receiver input is UART2(You can solder ELRS RX on UART2).
Power:
Input voltage: 3-6S
BEC: 5V/10V 3A max dual-channel BEC supports stable power supply on the sky side of DJI
LDO 3.3V: Max.1A
FC Firmware:
BetaFlight firmware: DAKEFPVF405
INAV firmware:DAKEFPVF405
Mounting:
Installation size: 30.5mm × 30.5mm The installation hole is M4 and supports shock column installation
External size 36mm × 36mm
Flight control weight: 6.9g
Flight control onboard voltage sensor.
F7 Flight Controller Specifications:
Name: F7 F722 flight controller
Main control chip: STM32F722RET6
MPU: MPU6500
Character overlay: AT7456E
Black box: integrated 16M Flash
Barometer: BMP280
Serial port: 6 optional
Motor output: 6 channels optional
LED strip: support
Buzzer: support
Camera_Control:support
Input voltage: 3-6S Lipo
Power output: 5V/2A, 9V/2A
Weight: 6.0g
Size: 36x36mm, mounting hole 30.5mm
Firmware: DAKEFPVF722
45A/60A BLHeli-S 3-6S DShot600 4-in-1 ESC:
Support Dshot600, Dshot300, Dshot150, Oneshot125, Multishot, PWM control signal
Power supply voltage: 3-6S (12-26V)
Continuous working current: 45A/60A
No built-in 5V BEC output
Firmware: BLHeli-S
Screw hole spacing: 30.5*30.5MM
Aperture: 4MM
Weight: 14.6g
– The ESC has an on-board filter capacitor that suppresses the back electromotive force, stabilizes the battery voltage, and protects the flight control ESC precision components.
– EMI Shell provides stronger anti-interference capability.
Note: There is no difference in appearance between the 45A and 60A ESCs, which can be distinguished from the MOS tube.
Note: Please be sure to connect the antenna reliably before connecting it to electricity. The adapter cable in our package is a feed line, not an antenna, and cannot be used as an antenna.
Model: Ultra1600 VTX 4.9G-5.8G 1.6W
Model: Ultra1600 VTX 4.9G-5.8G 1.6W
Input voltage: DC 7-36V(2-8S Battery)
Output: 5V@600mA(Power 5V to camera)
Input impedance: 75Ω
Protocol: IRC Tramp
Antenna connector: MMCX connector
Cable connector: GH1.25-6P connector
Output power: 25mW/200mW/400mW/800mW/1600mW/Pit mode
Frequency tables: 64 CH
Video format: PAL / NTSC
Microphone: Built in microphone
Size: 36.5mmx36.5mmx12mm
Weight: 15g(without cable)
Mounting holes: 30.5mmX30.5mm(M3)
Features
1. 1.6W super-power ,suitable for Long Range flight with good stability.
2. Six power levels: 25mW/200mW/400mW/800mW/1600mW/Pit mode .
3. Two-layer board cooling structure,separate power BEC and main-board,reducing
and shielding from the insinal interference.
4. Temperature control protection function that can prevent high temperature
burning.
5. Wide voltage input, supports 7V-36V voltage input.
6. VTX control protocol is IRC Tramp,supports OSD parameter adjustment.
7. VTX built in microphone,real-time return of Drone’s sounds.
8. Has 3 regional frequency tables to meet the needs of various regions.
9. One function buttons, three indicator lights, easy to operate.
10. Mounting holes is 30.5mmx30.5mm.
Support IRC Tramp Protocol
Ultra1600 VTX supports the IRC TRAMP protocol and the modification of
video transmission parameters through the remote control, including
frequency, working power and so on.
NOTE: For BetaFlight flight controller firmware above BetaFlight 4.1.0,you need
upload a VTX Table to the flight controller before using the remote control to
modify the video transmitter parameters normally.
ULTRA1600_VTX_16W.json
For the use of the video transmitter table, please refer to this article
“How to Setup Betaflight VTX Table – SmartAudio Tramp VTX Control”
Model: Ultra2500 2.5W VTX
Model: Ultra2500 VTX 4.9G-5.8G 2.5W
Input voltage: DC 7-36V(2-8S Battery)
Output: 5V@600mA(Power 5V to camera)
Input impedance: 75Ω
Protocol: IRC Tramp
Antenna connector: MMCX connector
Cable connector: GH1.25-6P connector
Output power: 25mW/400mW/800mW/1500mW/2500mW/Pit mode
Frequency tables: 64 CH
Video format: PAL / NTSC
Microphone: Built in microphone
Size: 36.5mmx36.5mmx12mm
Weight: 15g(without cable)
Mounting holes: 30.5mmX30.5mm(M3)
Features
1. 2.5W super-power ,suitable for Long Range flight with good stability.
2. Six power levels: 25mW/400mW/800mW/1500mW/2500mW/Pit mode .
3. Two-layer board cooling structure,separate power BEC and main-board,reducing
and shielding from the insinal interference.
4. Temperature control protection function that can prevent high temperature
burning.
5. Wide voltage input, supports 7V-36V voltage input.
6. VTX control protocol is IRC Tramp,supports OSD parameter adjustment.
7. VTX built in microphone,real-time return of Drone’s sounds.
8. Has 3 regional frequency tables to meet the needs of various regions.
9. One function buttons, three indicator lights, easy to operate.
10. Mounting holes is 30.5mmx30.5mm.
Support IRC Tramp Protocol
Ultra2500 VTX supports the IRC TRAMP protocol and the modification of
video transmission parameters through the remote control, including
frequency, working power and so on.
NOTE: For BetaFlight flight controller firmware above BetaFlight 4.1.0,you need
upload a VTX Table to the flight controller before using the remote control to
modify the video transmitter parameters normally.
ULTRA2500_VTX_25W.json
For the use of the video transmitter table, please refer to this article
“How to Setup Betaflight VTX Table – SmartAudio Tramp VTX Control”
NOTE:
Please pay attention to the choice of antenna for 4.9G or 5.8G.
For example, if you use 4.9G band, you have to use 4.9G antenna, if use 5.8G band, you have to use 5.8G antenna.
send it as your choice
